| 當前位置：首頁->方案設計 |
|
| MCP19118 數控模擬電源解決方案 |
|
|
| 文章來源： 更新時間：2014/11/3 10:27:00 |
在線咨詢： |
| |
Microchip公司的MCP19118/19是高度集成的混合信號模擬PWM電流模式控制器,并集成了用于DC/DC降壓應用的微控制器核.同步降壓器輸入電壓4.5V-40V,輸出電壓0.5V-3.6V,開關頻率100kHz到1.6MHz.PIC MCU核提供完整的定制化工作參數,起動和關斷性能,保護級別和故障處理程序.主要用在標準電源轉換,LED驅動器,電池充電等.本文介紹了MCP19118/19同步降壓和MCU核的主要特性,框圖,微控制器核框圖和應用電路,以及MCP19111 評估板主要特性,電路圖,材料清單和PCB設計圖.
The MCP19118/19 is a highly integrated, mixed signal, analog pulse-width modulation (PWM) current mode controller with an integrated microcontroller core for synchronous DC/DC step-down applications. Since the MCP19118/19 uses traditional analog control circuitry to regulate the output of the DC/DC converter, the integration of the PIC® microcontroller mid-range core is used to provide complete customization of device operating parameters, start-up and shutdown profiles, protection levels and fault handling procedures.
The MCP19118/19 is designed to efficiently operate from a single 4.5V to 40V supply. It features integrated synchronous drivers, bootstrap device, internal linear regulator and 4 kW nonvolatile memory, all in a space-saving 24-pin 4 mm x 4 mm QFN package (MCP19118) or 28-pin 5 mm x 5 mm QFN package (MCP19119).
After initial device configuration using Microchip’s MPLAB® X Integrated Development Environment (IDE) software, the PMBus or I2C can be used by a host to communicate with, or modify, the operation of the MCP19118/19.
Two internal linear regulators generate two 5V rails. One 5V rail is used to provide power for the internal analog circuitry and is contained on-chip. The second 5V rail provides power to the PIC device and is present on the VDD pin. It is recommended that a 1 μF capacitor be placed between VDD and PGND. The VDD pin may also be directly connected to the VDR pin or connected through a low-pass RC filter. The VDR pin provides power to the internal synchronous driver.
MCP19118/19同步降壓主要特性:
• Input Voltage: 4.5V to 40V
• Output Voltage: 0.5V to 3.6V
- Greater than 3.6V requires external divider
• Switching Frequency: 100 kHz to 1.6 MHz
• Quiescent Current: 5 mA Typical
• High-Drive:
- +5V Gate Drive
- 1A/2A Source Current
- 1A/2A Sink Current
• Low-Drive:
- +5V Gate Drive
- 2A Source Current
- 4A Sink Current
• Peak Current Mode Control
• Differential Remote Output Sense
• QEC-100 Qualified
• Multiple Output Systems:
- Master or Slave
- Frequency Synchronized
• Configurable Parameters:
- Overcurrent Limit
- Input Undervoltage Lockout
- Output Overvoltage
- Output Undervoltage
- Internal Analog Compensation
- Soft Start Profile
- Synchronous Driver Dead Time
- Switching Frequency
• Thermal Shutdown
MCP19118/19 MCU主要特性:
• Precision 8 MHz Internal Oscillator Block:
- Factory Calibrated
• Interrupt Capable
- Firmware
- Interrupt-on-Change Pins
• Only 35 Instructions to Learn
• 4096 Words On-Chip Program Memory
• High-Endurance Flash:
- 100,000 Write Flash Endurance
- Flash Retention: >40 years
• Watchdog Timer (WDT) with Independent
Oscillator for Reliable Operation
• Programmable Code Protection
• In-Circuit Debug (ICD) via Two Pins (MCP19119)
• In-Circuit Serial Programming™ (ICSP™) via Two Pins
• 11 I/O Pins and One Input-Only Pin (MCP19118)
- Three Open-Drain Pins
• 14 I/O Pins and One Input-Only Pin (MCP19119)
- Three Open-Drain Pins
• Analog-to-Digital Converter (ADC):
- 10-Bit Resolution
- 12 Internal Channels
- Eight External Channels
• Timer0: 8-Bit Timer/Counter with 8-Bit Prescaler
• Enhanced Timer1:
- 16-Bit Timer/Counter with Prescaler
- Two Selectable Clock Sources
• Timer2: 8-Bit Timer/Counter with Prescaler
- 8-Bit Period Register
• I2CTM Communication:
- 7-Bit Address Masking
- Two Dedicated Address Registers
- SMBus/PMBusTM Compatibility
圖1. MCP19118/19框圖
圖2. MCP19118/19微控制器核框圖
圖3. MCP19118/19典型應用電路圖
MCP19111 評估板
The MCP19111 is a digitally-enhanced PWM controller. It combines a pure-analog PWM controller with a supervisory microcontroller making it a fast, cost-effective, and configurable power conversion solution. The MCP19111 is ideal for standard power conversion, LED drivers, and battery charging applications. The MCP19111 Evaluation Board demonstrates how the MCP19111 device operates in a synchronous buck topology over a wide input voltage and load range. Nearly all operational and control system parameters are programmable by utilizing the integrated PIC microcontroller core. MPLAB X IDE can be used in conjunction with a Graphical User Interface (GUI) plug-in to easily configure the MCP19111. Alternatively, the user can program the MCP19111 using their own firmware, tailoring it to their application. The evaluation board contains headers for ICSP™ (In-Circuit Serial Programming™) as well as I2C communication, pull-up and pull-down resistor pads and test point pads on each GPIO pin, and two push buttons for system development
The MCP19111 Evaluation Board demonstrates how the MCP19111 device operates in a synchronous buck topology over a wide input voltage and load range. Nearly all operational and control system parameters are programmable by utilizing the integrated PIC microcontroller core. MPLAB X IDE can be used in conjunction with a Graphical User Interface (GUI) plug-in to easily configure the MCP19111. For more information regarding the GUI plug-in, refer to the “MCP19111 MPLAB® X Integrated Development Environment Plug-in User’s Guide” (DS52113). Alternatively, the user can program the MCP19111 using their own firmware, tailoring it to their application. The evaluation board contains headers for ICSP™ (In-Circuit Serial Programming™) as well as I2C communication, pull-up and pull-down resistor pads and test point pads on each GPIO pin, and two push buttons for system development. The MCP19111 Evaluation Board is also intended to demonstrate an optimized Printed Circuit Board (PCB) layout that minimizes parasitics while increasing efficiency and power density.
Proper PCB layout is critical to achieve optimum MCP19111 operation, as well as power train efficiency and noise minimization. MPLAB X IDE, the MCP19111 GUI plug-in, and example firmware is available for download from the Microchip website.
圖4.MCP19111 評估板外形圖
MCP19111 評估板主要特性:
The MCP19111 Evaluation Board provides the user with an example of an optimized PCB layout which reduces parasitics and increases power density. Some features of this board design include:
• Wide, short traces used to connect power components
• Ceramic VIN capacitors placed as close to the drain of the high-side MOSFET as possible, and as close to the source of the low-side MOSFET as possible
• Split ground plane to decouple the digital and power ground signals
• Careful placement of current sense components to reduce PCB induced noise
Vin range: 5V to 12V
Adjustable Vout range: 0.5V to 3.6V
Maximum output current: 30A with proper air flow
Programming and I2C communication headers
Factory programmed to produce 1.8V from 12V source
The factory programmed source code is available
圖5.MCP19111 評估板電路圖(1)
圖6.MCP19111 評估板電路圖(2)
MCP19111 評估板材料清單:
圖7.MCP19111 評估板PCB設計圖:頂層
圖8.MCP19111 評估板PCB設計圖:頂層銅線
圖9.MCP19111 評估板PCB設計圖:中間層1
圖10.MCP19111 評估板PCB設計圖:中間層2
圖11.MCP19111 評估板PCB設計圖:底層
圖12.MCP19111 評估板PCB設計圖:底層銅線 |
| |
|
|
|
|
|
| |
|
| |
|
|
